Description :  For the easy measurement of the outer diameter of pipes and other round objects

made of hardened steel with tips of tempered steel . 

Description :  For the outside measurement of threads .The tip are specially shaped to fit suitably

 to the threads . 

Description :  For measuring the outer diameter of pipes or cables which may have rims or other

obstructive shapes which would be difficult to measure with regular calipers .

Description :  For measuring the inside diameter of pipes , fittings , etc . Made of hardned steel

with points of tempered steel to prevent wear .

Description :  Has points of a share suitable to work in threads .

Description :  For measuring the inner diameter of equipment which may have rims or

obstructions which would make it difficult to measure with a regular caliper .

Description :  For measuring the thickness of the walls of pipes or valves , etc . Made of hardened

 steel with tempered steel points .

Description :  Made of hardened steel with points that are extra hard tempered for scribing

circles on iron plates .

Description :  A numeral counter indicates sizes simultaneously as the measurements are being taken . The display is very easy to read . Graduated in 0.01 mm increments from 25 mm to 500 mm on the standard size micrometer but micrometers up to 1,000 mm are also available upon request.

Description :  Each micrometer is equipped with a reries of interchangeable anvils . Each anvil is

marked to show its capacity and is fitted with an adjustable collar to prevent wear . Graduated in

0.01 mm increments .

Description :  Measures the depth of holes , projections , ect . Provided with a hardened tip and  threaded ground screw , adjustable for wear . The face of the base is hardener  tip and threaded ground screw , adjustable for wear . The face of the base is hardened and planed to maintain a level surface . Graduated in increments of 0.01 mm .

Description :  Particulary popular with machinists and tool makers for gauging narrow slots as well as for adjusting the air gaps of valves on motors. The leaves are made of tempered steel and have the thickness maked on them . The gauges listed below are classified as A type because they have straight leaves . Type B gauges with tapered leaves are also available upon request.

Description :  Made of high grade stainless steel with a satin chrome finish . Available in metric

graduation , or in both , metric and inch graduation .

Description :  Acompact , easy to use caliper graduated in 0.01 mm increments . All measurements shown on the digital display making it easier to take quick , precise measurements The graphic display will indicate wheather the tool is set for the measurement of inside or outside diameters .

Description :  Designed to quickly determine the picth of nut , bolt , and screw threads .

Description :  This balance is the most accurate of its type . Useful for most applications .

graduated in kilograms only .

Description :  Stainless steel or plastic made cup for measuring liquid volume . Graduated in liters only . 

Description : For weighing items in bulk . Capacity range from 200 grm to 20 kg . Available in

metric graduation only . Plastic or steel platform trays . 

Description :  Designed for heavy duty use in industry oa agriculture . Relieving gear prevents

gamage to the mechanism during loading and uploading to ensure a longer life . Fitted with

wheels for easy hanlding .

Description : Sellection of10 M / 15 M/ 20 M / 30 M ,  BOB 1 or BOB 3, with or with out Certificate.

 with approval sticker from Central Bureau of Weight and Measure. Direct imported from

"GERMANY".

Description :  These engineer's precision ruled are made of stainless ateel and dull chromed to

make the graduations easy to read . graduated in incrememts of 0.5 mm .

Description :  13 mm wide measuring tape available in linen , steel , or stainless steel . The tape is

 easy to ravel and unravel and the metric graduations are clearly visible . The tap is contained  in

 a black , vinyl laminated , metal case with a flush handle .

Description :  A paste for use with oil gauging tape . The colour of the paste will change from

yellow to red upon contact with water .

Description : A chemical paste used with oil gauging tapes of oils . The colour of the paste will generally change from light bule to red upon contact with oil . This paste will detect almost any kind of oil including mineral oil , vegetable oil , and animal oil , and solvents such as benzol , alcohol , acrylic solution , alkaline solution , and spirits .

Description :  For machinists and tool markers . Made of carbon tool steel . Two types are

available as listed below based upon  the degree of accuracy graduated flat squares are also

available upon request.

Description :  Recommended for use where extreme accuracy is required . Base and bladees are hardened , ground and lapped to insure that the square has a straight , parallel set up . 1st and 2 nd grades are available according to their tolerance. Non graduated types are most commonly used but graduated types are also available upon request . 

Description :  Combination sets are useful for all types of mechanical jobs . The set is comprised of a straight rule protractor , a square head , and a center head . The protractor is graduated to read from zero to 180 '' in both directions . The rule is made of stainless steel and is graduated in both 0.5 mm and 1 mm increments . The square head has a level and a scriber point . The protractor head , centre head , and square head are all made of cast iron .

Description :  Compact and lightweight . The housing is made of Nickel plated hexagonal brass .

Description :  A popular level made of cast iron . Provided with a level vail and a plumb vial .

Description :  These surface gauges are handy , well proportioned and rigid . Composed of a heavy , cast iron base and a mild steel rod supporting a scriber which has tempered points . Common sizes are listed below but gauges with longer spindles , up to 1,000 mm in the round base and 2,000 mm in the square base are available upon reqest .

Description :   A glass instrument for measuring the density and saturation of salf in seawater. A ballasted float carrying a scale that indicates density as related to fresh water. zero is 1,000 ; the density of seawater is about 1,026 ,but varies , in different areas between 1,000 and about 1,040

Description :   For measuring acidity and alkalinity ( hydrogen ion connectration ) based on a scale of 0 - 14 where 7 represents the value for pure water at 25 °C or neutrality. Values less than 7 represent increasing hydrogenion concentration or increasing acidity , and a value greater than 7 represents decreasing hydrogen-ion concentration or increasing alkalinity .

Description :   This range of guages is designed mainly for the measurement of cylinder bores but the ovality , taper , wear and other bore conditions may be measured with equal ease. Furnished without a dail gauge. when ordering , Please indicate if the dial gauge is required.

Description :  The internal mechanism for the pointer operation is filled with glycerine to protect

the accuracy of the gauge from mechanical vibration and to extend the working life of the

 gauge .

Description :  Designed for use with refrigerants that are not corrosive to bronze . Equipped with

a plain rotary , non - rust movement and a brass seamless bourdon spring . Brass case, self -

finish colour with brass ring .

Description :   For measuring temperature in a range of - 30 °C to +50 °C . The Overall lenght of  the thermometers is 250 mm and it is graduated in 10 ° increments .

Description :   Spare glass thermometers for the above brass cased test thermometers .

Description :   A unique system for determining the base number in both petroleum based and synthetic based oil . The kit brings accurate and reliable total base number analysis , and requires no calibration or instrumentation and uses no dangerous solvents or chemicals. TBN ( Total Base Number) is the measure of reserve alkalinity ( base) added to lubricating oils to protect the engine from the corrosive effects of acids formed during the combustion of fuels containing sulfur.